Welcome, Guest
Username: Password: Remember me

NOTE: This is a "Community" forum. Please be mindful that community members are here to help as part of a community effort. We therefore appreciate your effort in keeping this forum a happy place!

If you have a specific issue (e.g. hardware, failure) and want help from our support team, please use our tech support portal (Support menu - > Contact Us).
Thanks a lot of your help in making a better community.
  • Page:
  • 1

TOPIC:

Repeat outputs with crossovers on U-DAC8? 4 years 2 months ago #31819

  • zippy
  • zippy's Avatar Topic Author
  • Offline
  • New Member
  • New Member
  • Posts: 11
  • Thank you received: 1
Is it possible to setup multiple FL channel outputs each with their own crossovers?

IE:

Send output1 FL and crossover at 4k and up for tweeters, send output 2 FL and band pass 300-4k for midrange, send output3 FL and bandpass 80-300 for woofer, etc.....

I would like to use the U-DAC8 on a PC/MAC to send output to dedicated amps for each driver. I'm hoping to run full active to all channels of audio.

Side question, can I use multiple U-DAC8's on the same computer?
The following user(s) said Thank You: Jules

Please Log in or Create an account to join the conversation.

Repeat outputs with crossovers on U-DAC8? 4 years 2 months ago #31820

  • john.reekie
  • john.reekie's Avatar
  • Offline
  • Platinum Member
  • Platinum Member
  • Posts: 3775
  • Thank you received: 1588
Forgive me if this is obvious, but the U-DAC8 is only a DAC, there is no DSP in it. If you want crossovers on each channel, that will be up to the software running on your PC/Mac.
I am not miniDSP support.

"You must ask the right questions." - Dr. Alfred Lanning's hologram.
-> Have you read the User Manual??
-> Have you drawn and posted a diagram?
-> Have you posted a screenshot?
-> Have you posted your config file?
The following user(s) said Thank You: devteam

Please Log in or Create an account to join the conversation.

Repeat outputs with crossovers on U-DAC8? 4 years 2 months ago #31821

  • zippy
  • zippy's Avatar Topic Author
  • Offline
  • New Member
  • New Member
  • Posts: 11
  • Thank you received: 1
Thanks for the reply so quickly.

I'm looking at jrivier for the software to play through the U-DAC8. It supports defining channels in to out. I just am not sure if I can define the same channel more than once as a source.

Any insight for the second question at the end about support for 2 on the same computer?

Please Log in or Create an account to join the conversation.

Repeat outputs with crossovers on U-DAC8? 4 years 2 months ago #31822

  • john.reekie
  • john.reekie's Avatar
  • Offline
  • Platinum Member
  • Platinum Member
  • Posts: 3775
  • Thank you received: 1588
I have not done it, but you could look into Jack -

www.minidsp.com/forum/hardware-support/1...-2x4hd-under-windows

For crossover -

yabb.jriver.com/interact/index.php?topic=81448.0

hth :)
I am not miniDSP support.

"You must ask the right questions." - Dr. Alfred Lanning's hologram.
-> Have you read the User Manual??
-> Have you drawn and posted a diagram?
-> Have you posted a screenshot?
-> Have you posted your config file?
The following user(s) said Thank You: devteam

Please Log in or Create an account to join the conversation.

  • Page:
  • 1
Moderators: devteam