Welcome, Guest
Username: Password: Remember me
NOTE: This is a "Community" forum. Please be mindful that community members are here to help as part of a community effort. We therefore appreciate your effort in keeping this forum a happy place!

If you have a specific issue (e.g. hardware, failure) and want help from our support team, please use our tech support portal (Support menu - > Contact Us).
Thanks a lot of your help in making a better community.

TOPIC:

Coaxial digital output to AES3 input 1 year 7 months ago #46676

  • Ehcchan
  • Ehcchan's Avatar Topic Author
  • Offline
  • New Member
  • New Member
  • Posts: 18
  • Thank you received: 2
thx for your advice. Unfortunately, I don't have any DAC and oscilloscope.

Please Log in or Create an account to join the conversation.

Coaxial digital output to AES3 input 1 year 7 months ago #46682

  • dreite
  • dreite's Avatar
  • Offline
  • Platinum Member
  • Platinum Member
  • Posts: 1499
  • Thank you received: 686

thx for your advice. Unfortunately, I don't have any DAC and oscilloscope.

Well, maybe a friend with a DAC you could borrow?

According to Dutch and Dutch, an AES terminator plug is required on the last speaker in the chain. I assume you're using that? If so, try not using it since that will result in a higher voltage being present at your AES input.

I find it helpful many times to have a cheap DAC kicking around for just this type of troubleshooting. I have a Topping D30 that's been used multiple times for this kind of thing.

If you believe there's actually nothing at the SHD coax digital outputs, then you'll have to contact miniDSP for guidance.

Dave.

Please Log in or Create an account to join the conversation.

Coaxial digital output to AES3 input 1 year 7 months ago #46722

  • Dj7675
  • Dj7675's Avatar
  • Offline
  • Senior Member
  • Senior Member
  • Posts: 67
  • Thank you received: 18

This is what you need: www.amazon.com/Hosa-CDL-313-Coaxial-SPDI...U-Link/dp/B000068OGS

Then string one speaker to the other.

Or you should have just gotten the SHD Studio in the first place. I go SHD studio straight to my JBL 708p and then coax to a DAC to my single massive sub.

FYI, the 708p's don't terminate correctly if chaining them per the recommendation. If you go from a standard AES source to one speaker and then via the Digital Through to the other speaker, your source sees a 55 ohm termination, not 110 ohm. However, it still works okay.
Some other digital input monitors do this as well. That's why I was asking ehcchan about his specific speakers.

Dave.

I am daisy chaining to 708ps with SHD Studio is aes. What issues will this cause? Better to go direct to each speaker from the 2 aes outs on the studio?

Please Log in or Create an account to join the conversation.

Last edit: by Dj7675. Reason: Typo

Coaxial digital output to AES3 input 1 year 7 months ago #46723

  • jsimon7777
  • jsimon7777's Avatar
  • Offline
  • Junior Member
  • Junior Member
  • Posts: 23
  • Thank you received: 4
Zero issues. That is how I am doing it.

Please Log in or Create an account to join the conversation.

Coaxial digital output to AES3 input 1 year 7 months ago #46724

  • dreite
  • dreite's Avatar
  • Offline
  • Platinum Member
  • Platinum Member
  • Posts: 1499
  • Thank you received: 686

This is what you need: www.amazon.com/Hosa-CDL-313-Coaxial-SPDI...U-Link/dp/B000068OGS

Then string one speaker to the other.

Or you should have just gotten the SHD Studio in the first place. I go SHD studio straight to my JBL 708p and then coax to a DAC to my single massive sub.

FYI, the 708p's don't terminate correctly if chaining them per the recommendation. If you go from a standard AES source to one speaker and then via the Digital Through to the other speaker, your source sees a 55 ohm termination, not 110 ohm. However, it still works okay.
Some other digital input monitors do this as well. That's why I was asking ehcchan about his specific speakers.

Dave.

I am daisy chaining to 708p with SHD Studio is aes. What issues will this cause? Better to go direct to each speaker from the 2 aes outs on the studio?

The JBL's do not do the termination scheme correctly, but whether it causes issues depends much on the source characteristics.
Ideally, this should be done as "Ehcchan" related the Dutch and Dutch does it.....with no internal termination, but a movable XLR plug that provides the termination to the last device in the chain. In this way you could attach > 2 speakers to the system and not run into issues.

This is not unlike the CAN bus in your car, or an old-style 10base2 ethernet network, or many terminated network configurations.

If you attached 3-4 JBL 708 speakers to your chain, I suspect the setup would quit working.

Dave.

Please Log in or Create an account to join the conversation.

Coaxial digital output to AES3 input 1 year 7 months ago #46726

  • jsimon7777
  • jsimon7777's Avatar
  • Offline
  • Junior Member
  • Junior Member
  • Posts: 23
  • Thank you received: 4
The manual says a maximum of 4 speakers daisy chained.

Please Log in or Create an account to join the conversation.

Coaxial digital output to AES3 input 1 year 7 months ago #46728

  • dreite
  • dreite's Avatar
  • Offline
  • Platinum Member
  • Platinum Member
  • Posts: 1499
  • Thank you received: 686

The manual says a maximum of 4 speakers daisy chained.

It might still work, but the signal level will get pretty low.

Regardless, we're off the track of the original problem noted here.....which seems to be an invalid and/or missing S/PDIF data stream from an SHD unit. Since he doesn't have some test equipment nor another DAC to try, we're just spit-balling here.

Dave.

Please Log in or Create an account to join the conversation.

Coaxial digital output to AES3 input 1 year 7 months ago #46731

  • jsimon7777
  • jsimon7777's Avatar
  • Offline
  • Junior Member
  • Junior Member
  • Posts: 23
  • Thank you received: 4

The manual says a maximum of 4 speakers daisy chained.

It might still work, but the signal level will get pretty low.

Regardless, we're off the track of the original problem noted here.....which seems to be an invalid and/or missing S/PDIF data stream from an SHD unit. Since he doesn't have some test equipment nor another DAC to try, we're just spit-balling here.

Dave.


I would not expect the D&D to take coaxial input without a converter.

Please Log in or Create an account to join the conversation.

Coaxial digital output to AES3 input 1 year 7 months ago #46741

  • dreite
  • dreite's Avatar
  • Offline
  • Platinum Member
  • Platinum Member
  • Posts: 1499
  • Thank you received: 686

The manual says a maximum of 4 speakers daisy chained.

It might still work, but the signal level will get pretty low.

Regardless, we're off the track of the original problem noted here.....which seems to be an invalid and/or missing S/PDIF data stream from an SHD unit. Since he doesn't have some test equipment nor another DAC to try, we're just spit-balling here.

Dave.


I would not expect the D&D to take coaxial input without a converter.

Well, what you expect is beside the point. I've input a S/PDIF level signal into an AES input on numerous devices through the years. Generally, it does work.

Dave.

Please Log in or Create an account to join the conversation.

Coaxial digital output to AES3 input 1 year 7 months ago #46784

  • Ehcchan
  • Ehcchan's Avatar Topic Author
  • Offline
  • New Member
  • New Member
  • Posts: 18
  • Thank you received: 2
jsimon7777 is correct.

I have just received a AES/EBU Impedance Transformer Adapter (Neutrik NADITBNC-MX) and a BNC to RCA adapter. It simply works. This means impedance transformer is a must for D&D speaker in my case and SHD is just working fine. The sound is fantastic and just need to lower the volume because it becomes louder when compared with same level with the analog output.

Please Log in or Create an account to join the conversation.

Coaxial digital output to AES3 input 1 year 7 months ago #46785

  • dreite
  • dreite's Avatar
  • Offline
  • Platinum Member
  • Platinum Member
  • Posts: 1499
  • Thank you received: 686
Good deal.

A proper AES source level is 2V P-P minimum. So, you've accomplished the impedance transformation, but you still don't have a proper signal level. To really interface this correctly per the IEC 60958 standard, it requires an active interface device to raise the voltage level much higher. This would allow to drive a much longer cable as well......should you want to.

As I mentioned earlier, sometimes a simple interface without impedance correction will work....sometimes not. It depends upon both the source and load characteristics of the specific devices.

Dave.

Please Log in or Create an account to join the conversation.

Coaxial digital output to AES3 input 1 year 7 months ago #46787

  • jsimon7777
  • jsimon7777's Avatar
  • Offline
  • Junior Member
  • Junior Member
  • Posts: 23
  • Thank you received: 4
How long is the cable?

From what I have read, most spdif and aes implementations ignore unnecessary parts of the spec.

Please Log in or Create an account to join the conversation.

Coaxial digital output to AES3 input 1 year 7 months ago #46788

  • dreite
  • dreite's Avatar
  • Offline
  • Platinum Member
  • Platinum Member
  • Posts: 1499
  • Thank you received: 686

How long is the cable?

From what I have read, most spdif and aes implementations ignore unnecessary parts of the spec.

Regards the protocol, yes.
But the nominal signal levels are quite different though. And there's a large window variation that each device (source and/or load) might be tolerant of. Even with a transformer taking care of the impedance correction, the resultant signal level is still at the bottom of the specified minimum input range of an AES device.

His setup is working now, but I suspect it's on the hairy edge of not working. :) This is a situation where you're interfacing two non-compatible devices.....in the strictest sense.

For those interested, I suggest to read RaneNote 149 on their website.
www.nu9n.com/images/AES3-SPDIF-notes.pdf
Take special note of the "Conversion Caution" section.

Dave.

Please Log in or Create an account to join the conversation.

Coaxial digital output to AES3 input 1 year 7 months ago #46791

  • Ehcchan
  • Ehcchan's Avatar Topic Author
  • Offline
  • New Member
  • New Member
  • Posts: 18
  • Thank you received: 2
It is 2m long.

Please Log in or Create an account to join the conversation.

Coaxial digital output to AES3 input 1 year 7 months ago #46792

  • jsimon7777
  • jsimon7777's Avatar
  • Offline
  • Junior Member
  • Junior Member
  • Posts: 23
  • Thank you received: 4

It is 2m long.


From what I've read, that length would be too long without the impedance adapter. That you otherwise get reflections on the cable.

Please Log in or Create an account to join the conversation.

Moderators: devteam