Welcome, Guest
Username: Password: Remember me

NOTE: This is a "Community" forum. Please be mindful that community members are here to help as part of a community effort. We therefore appreciate your effort in keeping this forum a happy place!

If you have a specific issue (e.g. hardware, failure) and want help from our support team, please use our tech support portal (Support menu - > Contact Us).
Thanks a lot of your help in making a better community.
  • Page:
  • 1

TOPIC:

Only sub output from 2.1 setup via Calibration 6 years 4 months ago #32081

  • Heinebodekaer
  • Heinebodekaer's Avatar Topic Author
  • Offline
  • New Member
  • New Member
  • Posts: 3
  • Thank you received: 2
Hi everyone,

I'm doing subwoofer Integration with the DDRC-24 from (www.minidsp.com/applications/digital-roo...rc-24-for-2-1-system). I get through the first part fine and if I try music after this part I get signal for both the speakers and the sub. However when I try and use the calibration tool it only sends signal out to the sub.

Have anyone else had this problem or know what might be the reason?

Confused regards

Heine

Please Log in or Create an account to join the conversation.

Only sub output from 2.1 setup via Calibration 6 years 4 months ago #32082

  • john.reekie
  • john.reekie's Avatar
  • Offline
  • Platinum Member
  • Platinum Member
  • Posts: 3778
  • Thank you received: 1594
Can you post a screenshot of your routing table?

Please Log in or Create an account to join the conversation.

Only sub output from 2.1 setup via Calibration 6 years 4 months ago #32086

  • Heinebodekaer
  • Heinebodekaer's Avatar Topic Author
  • Offline
  • New Member
  • New Member
  • Posts: 3
  • Thank you received: 2
Thank you very much for trying to help me.

I've attached a screenshot of the routing table.
Attachments:

Please Log in or Create an account to join the conversation.

Only sub output from 2.1 setup via Calibration 6 years 4 months ago #32117

  • john.reekie
  • john.reekie's Avatar
  • Offline
  • Platinum Member
  • Platinum Member
  • Posts: 3778
  • Thank you received: 1594
Well that looks fine. I can't think of what would be causing what you are observing. All I can suggest is work through the Troubleshooting in the manual - check your cabling etc. Make sure you have latest software and firmware installed (if you open a ticket that would probably be the first thing anyway).

Also, make sure to quit DDRC-24 plugin before starting DLCT.

FWIW I ran a calibration last night with the same configuration as you have there and it worked without any issues.

Please Log in or Create an account to join the conversation.

Last edit: by john.reekie.

Only sub output from 2.1 setup via Calibration 6 years 3 months ago #32165

  • devteam
  • devteam's Avatar
  • Away
  • Administrator
  • Administrator
  • Posts: 9180
  • Thank you received: 1489
@ Heinebodekaer

Very odd indeed.
1) Please try a restore to default all from the DDRC-24.
2) Reconfigure the plugin as you did. Don't forget the output crossover section.
3) Make sure that you play music to the plugin (without Dirac and you indeed get a 2.1 system).
4) Move to Dirac setup.

HTH
miniDSP, building a DSP community one board at a time.

For any official support, please contact our technical support team directly @ support.minidsp.com/support/home

Please Log in or Create an account to join the conversation.

Only sub output from 2.1 setup via Calibration 6 years 3 months ago #32246

  • Heinebodekaer
  • Heinebodekaer's Avatar Topic Author
  • Offline
  • New Member
  • New Member
  • Posts: 3
  • Thank you received: 2
Hi,

I did a reset of the minidsp and then everything worked fine.

Case closed and thank you for all the help.
The following user(s) said Thank You: devteam, john.reekie

Please Log in or Create an account to join the conversation.

  • Page:
  • 1
Moderators: devteam