Welcome, Guest
Username: Password: Remember me

NOTE: This is a "Community" forum. Please be mindful that community members are here to help as part of a community effort. We therefore appreciate your effort in keeping this forum a happy place!

If you have a specific issue (e.g. hardware, failure) and want help from our support team, please use our tech support portal (Support menu - > Contact Us).
Thanks a lot of your help in making a better community.
  • Page:
  • 1

TOPIC:

Using remote trigger with conventional 3.5mm jack 1 year 2 months ago #50370

  • asx77
  • asx77's Avatar Topic Author
  • Away
  • Platinum Member
  • Platinum Member
  • Posts: 352
  • Thank you received: 50
Guys,

If I was to fit the C-DSP 8x12 between a streamer and amp (both with conventional 3.5mm 12v trigger in/out) how could I get the C-DSP to auto turn on?

Option 1: 12v trigger out from streamer to C-DSP. Then trigger out from C-DSP to the amp. I think the amp expects to see a 12v signal, so if the C-DSP doesn't pass through the voltage from the streamer then this might not work. If it does then do I simply use 3.5mm jack at one end and bare wire at the other? Presume the only important wire here is the positive.

Option 2: Plug a Y-Splitter into the streamer's 3.5mm 12v out jack. Then send a 3.5mm to 3.5mm to the amp and another 3.5mm to bare wire to the C-DSP.

What are your thoughts?
Thanks

Please Log in or Create an account to join the conversation.

Using remote trigger with conventional 3.5mm jack 1 year 2 months ago #50386

  • danthe0
  • danthe0's Avatar
  • Offline
  • Senior Member
  • Senior Member
  • Posts: 58
  • Thank you received: 18
More info on products used ?
I don't think 3.5mm TRS jack is conventionally used for 12V trigger... Isn't it usually for unbalanced audio with Left (Tip), Right (Ring), Signal Ground (Sleeve) ? The other case I've seen was RS232C with Transmit (Tip), Receive (Ring), Signal Ground (Sleeve).

You could run the CDSP in always on mode by setting the slide switch in the left position, but it'll suck 10W constantly from the wall and it gets a tad warm.

Please Log in or Create an account to join the conversation.

Using remote trigger with conventional 3.5mm jack 1 year 2 months ago #50387

  • asx77
  • asx77's Avatar Topic Author
  • Away
  • Platinum Member
  • Platinum Member
  • Posts: 352
  • Thank you received: 50
Hi,
It’s definitely a 3.5mm jack. Just a mono version although I’m told stereo would also work. It’s between a Primare NP30 and a Krell KAV 400xi. I want to slot the C-DSP between them if possible.

When I turn the Primare on, I want to trigger the CDSP then have it turn the Krell on.

Thanks

Please Log in or Create an account to join the conversation.

Using remote trigger with conventional 3.5mm jack 1 year 1 month ago #50394

  • danthe0
  • danthe0's Avatar
  • Offline
  • Senior Member
  • Senior Member
  • Posts: 58
  • Thank you received: 18
If the streamer and amp's REM trigger was already working, it should be fine to sandwich the CDSP in between them. Check voltages to be sure. The NP30 manual is too barebones and gives no hint.
Option 1 would be the way to go.
Just set the CDSP slide switch at Mid position/Position 2.
You probably might need to tie the REM IN and REM OUT grounds together.


Option 2 might introduce some pop if the amp turns on before the DSP fully turns on.
The following user(s) said Thank You: asx77

Please Log in or Create an account to join the conversation.

Last edit: by danthe0.

Using remote trigger with conventional 3.5mm jack 1 year 3 weeks ago #50900

  • asx77
  • asx77's Avatar Topic Author
  • Away
  • Platinum Member
  • Platinum Member
  • Posts: 352
  • Thank you received: 50
Hi,
I never thanked you for your thoughts on this.

Thanks!

Please Log in or Create an account to join the conversation.

  • Page:
  • 1
Moderators: devteam