Welcome, Guest
Username: Password: Remember me
NOTE: This forum is community powered. Please be mindful that long time community members are here to help as part of a community effort. If you have a specific issue (e.g. hardware, failure), please use our tech support portal (Support menu - > Contact Us). Thanks a lot of your help in making a better community. :-)

TOPIC: Can the PWR-ICE125WD be disassembled easily?

Can the PWR-ICE125WD be disassembled easily? 3 months 20 hours ago #27560

  • bcodemz
  • bcodemz's Avatar
  • Offline
  • Senior Boarder
  • Posts: 44
  • Thank you received: 2
  • Karma: 1
Hi,

Does anyone know if the PWR-ICE125WD can be disassembled easily? I want to disassemble it and just put the amp module inside a speaker.
The administrator has disabled public write access.

Can the PWR-ICE125WD be disassembled easily? 3 months 17 hours ago #27573

  • devteam
  • devteam's Avatar
  • Offline
  • Administrator
  • Posts: 5108
  • Thank you received: 632
  • Karma: 119
Sure, not a problem to do so.. Just make sure that you use the RCA input buffer board as the IcePower requires a special loading.

Devteam
MiniDSP, building a DIY DSP community one board at a time.
The administrator has disabled public write access.

Can the PWR-ICE125WD be disassembled easily? 1 month 1 week ago #28430

Hi,

How is the volume potentiometer removed from the plate?
The administrator has disabled public write access.

Can the PWR-ICE125WD be disassembled easily? 1 month 1 week ago #28491

  • devteam
  • devteam's Avatar
  • Offline
  • Administrator
  • Posts: 5108
  • Thank you received: 632
  • Karma: 119
@ Vaniljeansigt

It's on the board with the RCA buffer. It's one PCB for pot + RCA. Remove the knob of the pot, remove the bolt holding the RCA. (see rear pic of the unit on product page to see that one PCB we're talking about. Do you have a PWR_ICE already or just asking hypothetically?

DevTeam
MiniDSP, building a DIY DSP community one board at a time.
The administrator has disabled public write access.

Can the PWR-ICE125WD be disassembled easily? 1 month 1 week ago #28504

I have the PWR ICE already, and tried to remove to knob, but was afraid I was using too much force. Do I just pull the knob outwards?
The administrator has disabled public write access.

Can the PWR-ICE125WD be disassembled easily? 1 month 6 days ago #28541

  • devteam
  • devteam's Avatar
  • Offline
  • Administrator
  • Posts: 5108
  • Thank you received: 632
  • Karma: 119
@ Vaniljeansigt

There is a "plastic knob" on the pot. You need to remove it (i.e. pull it outward) then you can unscrew the bolt from the plate so the PCB can move out. Plastic knob always fit on a pot with a press fit. Google video maybe to see..

DevTeam
MiniDSP, building a DIY DSP community one board at a time.
The administrator has disabled public write access.

Can the PWR-ICE125WD be disassembled easily? 2 weeks 5 hours ago #28897

Thank you for your help.
I've tried to pull as hard as I can on the knob on two different modules, but I cannot remove the knob.
I could not find any guide on YouTube on how to do it. If you have I link I'll be happy to watch it :)
Is it certain that no glue has been added to the knob?
The administrator has disabled public write access.

Can the PWR-ICE125WD be disassembled easily? 2 weeks 1 hour ago #28899

  • dreite
  • dreite's Avatar
  • Offline
  • Platinum Boarder
  • Posts: 842
  • Thank you received: 408
  • Karma: 78
You need a YT video to remove a knob? :)
I just removed mine....took about five seconds. It has a fairly tight fit (which it should) so just stick a small screwdriver underneath and gently pry it up/off.

Dave.


This message has an attachment image.
Please log in or register to see it.

The administrator has disabled public write access.
The following user(s) said Thank You: devteam, Vaniljeansigt
Time to create page: 0.131 seconds