Welcome, Guest
Username: Password: Remember me
Forgot your password? Forgot your username? Create an account
Forum
Community Support
nanoAVR
NanoAVR DL - How to set-up a 5.0 system correctly
NOTE: This forum is community powered. Please be mindful that long time community members are here to help as part of a community effort. If you have a specific issue (e.g. hardware, failure), please use our tech support portal (Support menu - > Contact Us). Thanks a lot of your help in making a better community. :-)

TOPIC: NanoAVR DL - How to set-up a 5.0 system correctly

NanoAVR DL - How to set-up a 5.0 system correctly 3 years 8 months ago #19997

  • bibi.b
  • bibi.b's Avatar
  • Offline
  • Fresh Boarder
  • Posts: 6
  • Karma: 0
Hello,

I have a 5.0 system with 2 large fronts, 2 large rears and a bigger center. Manual reads to set-up the measurement with 7.1 system. But wouldn't it be better to choose "custom" and tell the system what is really attached?

Thanks
Meiko
Last Edit: 3 years 8 months ago by bibi.b.
The administrator has disabled public write access.

NanoAVR DL - How to set-up a 5.0 system correctly 3 years 8 months ago #20024

  • john.reekie
  • john.reekie's Avatar
  • Offline
  • Platinum Boarder
  • Posts: 3263
  • Thank you received: 1403
  • Karma: 131
The system config that you choose in the nanoAVR DL needs to be for the signal that is going through it, not the final number of speakers. Typically the source material will be 7.1, and that may be downmixed in the AVR. So in that typical case the system config chosen in the nanoAVR DL would be 7.1. However it may be that your setup is not like that - perhaps you could provide more specifics?
I am not miniDSP support.

"You must ask the right questions." - Dr. Alfred Lanning's hologram.
-> Have you read the User Manual??
-> Have you drawn and posted a diagram?
-> Have you posted a screenshot?
-> Have you posted your config file?
The administrator has disabled public write access.
The following user(s) said Thank You: devteam

NanoAVR DL - How to set-up a 5.0 system correctly 3 years 8 months ago #20031

  • bibi.b
  • bibi.b's Avatar
  • Offline
  • Fresh Boarder
  • Posts: 6
  • Karma: 0
Thanks for your reply. Makes sense!

So the NanoAVR is not capable of downmixing. My Onkyo AVR is by the way...
Is it - in my case - okay to link the LFE channel with the front? Because It is the same speaker for the low frequencies...?
The administrator has disabled public write access.

NanoAVR DL - How to set-up a 5.0 system correctly 3 years 7 months ago #20073

  • devteam
  • devteam's Avatar
  • Offline
  • Administrator
  • Posts: 8116
  • Thank you received: 952
  • Karma: 150
That's correct, the nanoAVR won't be the device doing the downmixing. Best that you do that with your AVR. i.e. need to redirect the bass I guess since you have no subs. Best that you configure your AVR correctly (i.e. 5.0 setup) and it might automatically do that redirect. Then when you do the sweeps through the nanoAVR, it will go to the correct speakers.

DevTeam
MiniDSP, building a DIY DSP community one board at a time.
The administrator has disabled public write access.
Moderators: devteam
Forum
Community Support
nanoAVR
NanoAVR DL - How to set-up a 5.0 system correctly
Time to create page: 0.107 seconds