Welcome, Guest
Username: Password: Remember me
NOTE: This forum is community powered. Please be mindful that long time community members are here to help as part of a community effort. If you have a specific issue (e.g. hardware, failure), please use our tech support portal (Support menu - > Contact Us). Thanks a lot of your help in making a better community. :-)

TOPIC: Adjust calculated delays?

Adjust calculated delays? 2 weeks 2 days ago #40399

  • chrisgeary
  • chrisgeary's Avatar
  • Offline
  • Fresh Boarder
  • Posts: 11
  • Karma: 0
I notice that if I examine the DDRC-88D with the DDRC-88-BM tool, it shows me the delays configured on each channel. It seems to have applied 0.13ms on the front left vs 0ms on the front right and 4.88 on the rear left vs 5.08ms on the rear right. This is after the full suite of measurements took place. The end result seems to be messing up imaging. Can I manually adjust those delays?
The administrator has disabled public write access.

Adjust calculated delays? 2 weeks 1 day ago #40418

  • john.reekie
  • john.reekie's Avatar
  • Offline
  • Platinum Boarder
  • Posts: 3263
  • Thank you received: 1403
  • Karma: 131
I believe it's the first measurement that sets the delays. You could try using a tape measure to set the exact position of the microphone for that first measurement.
Or, you could add delays on the output channels to get them to match.
I am not miniDSP support.

"You must ask the right questions." - Dr. Alfred Lanning's hologram.
-> Have you read the User Manual??
-> Have you drawn and posted a diagram?
-> Have you posted a screenshot?
-> Have you posted your config file?
The administrator has disabled public write access.

Adjust calculated delays? 2 weeks 1 day ago #40419

  • chrisgeary
  • chrisgeary's Avatar
  • Offline
  • Fresh Boarder
  • Posts: 11
  • Karma: 0
How do I add delays to the output channels? There seems to be no way to modify anything in the DDRC-88-BM tool. Connect, Config1/2/3/4 and Dirac Live On/Off seem the only things that are clickable.
The administrator has disabled public write access.

Adjust calculated delays? 2 weeks 1 day ago #40421

  • john.reekie
  • john.reekie's Avatar
  • Offline
  • Platinum Boarder
  • Posts: 3263
  • Thank you received: 1403
  • Karma: 131
I'm not really following, if you go to the Outputs tab, the delay setting is near the bottom of each channel.
I am not miniDSP support.

"You must ask the right questions." - Dr. Alfred Lanning's hologram.
-> Have you read the User Manual??
-> Have you drawn and posted a diagram?
-> Have you posted a screenshot?
-> Have you posted your config file?
The administrator has disabled public write access.

Adjust calculated delays? 2 weeks 1 day ago #40422

  • chrisgeary
  • chrisgeary's Avatar
  • Offline
  • Fresh Boarder
  • Posts: 11
  • Karma: 0
It's greyed out. The only tab that is not is the Dirac tab.
The administrator has disabled public write access.

Adjust calculated delays? 2 weeks 1 day ago #40423

  • john.reekie
  • john.reekie's Avatar
  • Offline
  • Platinum Boarder
  • Posts: 3263
  • Thank you received: 1403
  • Karma: 131
Ohhhh... right. Then I think you don't have the BM feature enabled. Sorry, I forgot that there is a "no BM" mode :blush:
I am not miniDSP support.

"You must ask the right questions." - Dr. Alfred Lanning's hologram.
-> Have you read the User Manual??
-> Have you drawn and posted a diagram?
-> Have you posted a screenshot?
-> Have you posted your config file?
The administrator has disabled public write access.
Moderators: devteam
Time to create page: 0.108 seconds