Welcome, Guest
Username: Password: Remember me
NOTE: This forum is community powered. Please be mindful that long time community members are here to help as part of a community effort. If you have a specific issue (e.g. hardware, failure), please use our tech support portal (Support menu - > Contact Us). Thanks a lot of your help in making a better community. :-)

TOPIC: no soundstage.

no soundstage. 3 weeks 2 days ago #40257

  • joegjr1
  • joegjr1's Avatar
  • Offline
  • Fresh Boarder
  • Posts: 7
  • Thank you received: 1
  • Karma: 0
Using a pair of maggies, all the sound is coming from the center.Very strange for maggies, they usually are very expansive extending beyond the speakers as well as behind and holographic-ally. That's what I like them better than most others. On the plus side they seem to be more alive than they were before correction.
The administrator has disabled public write access.

no soundstage. 3 weeks 2 days ago #40260

  • john.reekie
  • john.reekie's Avatar
  • Offline
  • Platinum Boarder
  • Posts: 3263
  • Thank you received: 1403
  • Karma: 131
Hi, what does your routing matrix look like? The default setting is for a two-way crossover, so you probably want to change it if you haven't already. See page 21 of user manual.
I am not miniDSP support.

"You must ask the right questions." - Dr. Alfred Lanning's hologram.
-> Have you read the User Manual??
-> Have you drawn and posted a diagram?
-> Have you posted a screenshot?
-> Have you posted your config file?
The administrator has disabled public write access.
The following user(s) said Thank You: joegjr1

no soundstage. 3 weeks 1 day ago #40265

  • joegjr1
  • joegjr1's Avatar
  • Offline
  • Fresh Boarder
  • Posts: 7
  • Thank you received: 1
  • Karma: 0
Right now I am using pg. 22 matrix because I am using a sub. If you feel that I still to go with pg. 21 matrix I will do so.

thank you,
Joe
The administrator has disabled public write access.

no soundstage. 3 weeks 1 day ago #40270

  • joegjr1
  • joegjr1's Avatar
  • Offline
  • Fresh Boarder
  • Posts: 7
  • Thank you received: 1
  • Karma: 0
Ok I have made those changes and I do have to say it has opened up. Imaging is dead on, as good as I've heard from any of my past systems. Again. a big thank you again John.

Joe
The administrator has disabled public write access.

no soundstage. 2 weeks 6 days ago #40281

  • john.reekie
  • john.reekie's Avatar
  • Offline
  • Platinum Boarder
  • Posts: 3263
  • Thank you received: 1403
  • Karma: 131
Sure, no worries :) If you decide to put the sub back in, maybe just check that the low pass filter is enabled on it.
I am not miniDSP support.

"You must ask the right questions." - Dr. Alfred Lanning's hologram.
-> Have you read the User Manual??
-> Have you drawn and posted a diagram?
-> Have you posted a screenshot?
-> Have you posted your config file?
The administrator has disabled public write access.

no soundstage. 2 weeks 6 days ago #40287

  • joegjr1
  • joegjr1's Avatar
  • Offline
  • Fresh Boarder
  • Posts: 7
  • Thank you received: 1
  • Karma: 0
Just for the hell of it I did another room correction and realized that I had set up the microphone placements to close together, that is why all the sound was centered down the middle as if I had a center channel. I did it all over again and this time I spread them out about 3 ft on each side of the center position and a foot lower and higher at each position. That did it. I also put the sub back in and have a big smile on my face.
The administrator has disabled public write access.
Moderators: devteam
Time to create page: 0.105 seconds