Welcome, Guest
Username: Password: Remember me
NOTE: This forum is community powered. Please be mindful that long time community members are here to help as part of a community effort. If you have a specific issue (e.g. hardware, failure), please use our tech support portal (Support menu - > Contact Us). Thanks a lot of your help in making a better community. :-)

TOPIC: Only sub output from 2.1 setup via Calibration

Only sub output from 2.1 setup via Calibration 1 month 3 weeks ago #32081

  • Heinebodekaer
  • Heinebodekaer's Avatar
  • Offline
  • Fresh Boarder
  • Posts: 3
  • Thank you received: 2
  • Karma: 0
Hi everyone,

I'm doing subwoofer Integration with the DDRC-24 from (www.minidsp.com/applications/digital-roo...rc-24-for-2-1-system). I get through the first part fine and if I try music after this part I get signal for both the speakers and the sub. However when I try and use the calibration tool it only sends signal out to the sub.

Have anyone else had this problem or know what might be the reason?

Confused regards

Heine
The administrator has disabled public write access.

Only sub output from 2.1 setup via Calibration 1 month 3 weeks ago #32082

  • john.reekie
  • john.reekie's Avatar
  • Offline
  • Platinum Boarder
  • Posts: 2682
  • Thank you received: 1096
  • Karma: 110
Can you post a screenshot of your routing table?
I am not miniDSP support.

"You must ask the right questions." - Dr. Alfred Lanning's hologram.
-> Have you read the User Manual??
-> Have you drawn and posted a diagram?
-> Have you posted a screenshot?
-> Have you posted your config file?
The administrator has disabled public write access.

Only sub output from 2.1 setup via Calibration 1 month 3 weeks ago #32086

  • Heinebodekaer
  • Heinebodekaer's Avatar
  • Offline
  • Fresh Boarder
  • Posts: 3
  • Thank you received: 2
  • Karma: 0
Thank you very much for trying to help me.

I've attached a screenshot of the routing table.

This message has an attachment image.
Please log in or register to see it.

The administrator has disabled public write access.

Only sub output from 2.1 setup via Calibration 1 month 3 weeks ago #32117

  • john.reekie
  • john.reekie's Avatar
  • Offline
  • Platinum Boarder
  • Posts: 2682
  • Thank you received: 1096
  • Karma: 110
Well that looks fine. I can't think of what would be causing what you are observing. All I can suggest is work through the Troubleshooting in the manual - check your cabling etc. Make sure you have latest software and firmware installed (if you open a ticket that would probably be the first thing anyway).

Also, make sure to quit DDRC-24 plugin before starting DLCT.

FWIW I ran a calibration last night with the same configuration as you have there and it worked without any issues.
I am not miniDSP support.

"You must ask the right questions." - Dr. Alfred Lanning's hologram.
-> Have you read the User Manual??
-> Have you drawn and posted a diagram?
-> Have you posted a screenshot?
-> Have you posted your config file?
Last Edit: 1 month 3 weeks ago by john.reekie.
The administrator has disabled public write access.

Only sub output from 2.1 setup via Calibration 1 month 3 weeks ago #32165

  • devteam
  • devteam's Avatar
  • Online
  • Administrator
  • Posts: 5722
  • Thank you received: 702
  • Karma: 132
@ Heinebodekaer

Very odd indeed.
1) Please try a restore to default all from the DDRC-24.
2) Reconfigure the plugin as you did. Don't forget the output crossover section.
3) Make sure that you play music to the plugin (without Dirac and you indeed get a 2.1 system).
4) Move to Dirac setup.

HTH
MiniDSP, building a DIY DSP community one board at a time.
The administrator has disabled public write access.

Only sub output from 2.1 setup via Calibration 1 month 2 weeks ago #32246

  • Heinebodekaer
  • Heinebodekaer's Avatar
  • Offline
  • Fresh Boarder
  • Posts: 3
  • Thank you received: 2
  • Karma: 0
Hi,

I did a reset of the minidsp and then everything worked fine.

Case closed and thank you for all the help.
The administrator has disabled public write access.
The following user(s) said Thank You: devteam, john.reekie
Time to create page: 0.117 seconds