Welcome, Guest
Username: Password: Remember me
NOTE: This forum is community powered. Please be mindful that long time community members are here to help as part of a community effort. If you have a specific issue (e.g. hardware, failure), please use our tech support portal (Support menu - > Contact Us). Thanks a lot of your help in making a better community. :-)

TOPIC: DDRC-88A - nanoAVR DL as only test playback device

DDRC-88A - nanoAVR DL as only test playback device 1 year 8 months ago #18309

  • marmasotti
  • marmasotti's Avatar
  • Offline
  • Senior Boarder
  • Posts: 48
  • Thank you received: 1
  • Karma: 0
Using the DLCT program, I can't proceed because the only test signal playback device among the displayed options is the nanoAVR DL, instead the DDRC-88A device as adviced in the user manual.
DLCT is v1.0.5 with Windows7 64-bit edition. Thank you for any ideas, Marco
The administrator has disabled public write access.

DDRC-88A - nanoAVR DL as only test playback device 1 year 8 months ago #18310

  • dgemma
  • dgemma's Avatar
  • Offline
  • Fresh Boarder
  • Posts: 1
  • Karma: 0
marmasotti wrote:
Using the DLCT program, I can't proceed because the only test signal playback device among the displayed options is the nanoAVR DL, instead the DDRC-88A device as adviced in the user manual.
DLCT is v1.0.5 with Windows7 64-bit edition. Thank you for any ideas, Marco

Marco,

Are you sure you cannot proceed? This occurred when I set up my 88A last night, however it did not keep me from running a full calibration. I intend to open a support ticket unless "devteam" can explain why this is happening to both of us. It is currently 6:30AM in Hong Kong so hopefully someone will be able to address this soon...

Edit: A post on AVSForum indicates this is normal behavior, however I cannot find an official source: www.avsforum.com/forum/90-receivers-amps...21.html#post30721809
Last Edit: 1 year 8 months ago by dgemma.
The administrator has disabled public write access.

DDRC-88A - nanoAVR DL as only test playback device 1 year 8 months ago #18311

  • john.reekie
  • john.reekie's Avatar
  • Offline
  • Platinum Boarder
  • Posts: 2286
  • Thank you received: 861
  • Karma: 99
If it's showing nanoAVR DL, it will work.
I am not miniDSP support.

"You must ask the right questions." - Dr. Alfred Lanning's hologram.
-> Have you read the User Manual??
-> Have you drawn and posted a diagram?
-> Have you posted a screenshot?
-> Have you posted your config file?
The administrator has disabled public write access.
The following user(s) said Thank You: marmasotti

DDRC-88A - nanoAVR DL as only test playback device 1 year 8 months ago #18314

  • marmasotti
  • marmasotti's Avatar
  • Offline
  • Senior Boarder
  • Posts: 48
  • Thank you received: 1
  • Karma: 0
Actually, I even didn't try to go further through the menu to avoid mess.
If the identifier, recognized differently, works the same I then will not care. I'll report on this later on the day.
However, the question remains, maybe wrong firmware, which is 2.16 in my unit?
Thanks, Marco
The administrator has disabled public write access.

DDRC-88A - nanoAVR DL as only test playback device 1 year 8 months ago #18315

  • john.reekie
  • john.reekie's Avatar
  • Offline
  • Platinum Boarder
  • Posts: 2286
  • Thank you received: 861
  • Karma: 99
Hi Marco, the number sounds right but I'll check my unit later this evening. I'm pretty sure I'm on the latest version and it still says "nanoAVR DL".
I am not miniDSP support.

"You must ask the right questions." - Dr. Alfred Lanning's hologram.
-> Have you read the User Manual??
-> Have you drawn and posted a diagram?
-> Have you posted a screenshot?
-> Have you posted your config file?
The administrator has disabled public write access.

DDRC-88A - nanoAVR DL as only test playback device 1 year 8 months ago #18324

  • john.reekie
  • john.reekie's Avatar
  • Offline
  • Platinum Boarder
  • Posts: 2286
  • Thank you received: 861
  • Karma: 99
Hi again Marco, my unit reports as 2.16 in DDRC-88 Utility and works fine.

HTH
I am not miniDSP support.

"You must ask the right questions." - Dr. Alfred Lanning's hologram.
-> Have you read the User Manual??
-> Have you drawn and posted a diagram?
-> Have you posted a screenshot?
-> Have you posted your config file?
The administrator has disabled public write access.
The following user(s) said Thank You: devteam

DDRC-88A - nanoAVR DL as only test playback device 1 year 8 months ago #18340

  • marmasotti
  • marmasotti's Avatar
  • Offline
  • Senior Boarder
  • Posts: 48
  • Thank you received: 1
  • Karma: 0
Yes, my unit works fine too, as far as I can see a different name might not be a concern.
Thank you, marco
The administrator has disabled public write access.

DDRC-88A - nanoAVR DL as only test playback device 1 year 8 months ago #18514

  • devteam
  • devteam's Avatar
  • Online
  • Administrator
  • Posts: 5123
  • Thank you received: 632
  • Karma: 119
No need to worry Marco. nanoAVR or DDRC use similar software/firmware base. It's just a reporting that we've fixed in latest firmware issues.
Your unit will work fine. :-)

DevTeam
MiniDSP, building a DIY DSP community one board at a time.
The administrator has disabled public write access.
Time to create page: 0.134 seconds